Skip to content
FREE SHIPPING ON ALL ORDERS $500 OR MORE
FREE SHIPPING ON ALL ORDERS $500 OR MORE

CeRam Kote 426 Ceramic - 1 Gal Kit

$277.48
SKU CK426-1G

CeRam-Kote 426 is a unique ceramic coating that prevents corrosion in water service applications. It is designed to work as a barrier coat in combination with Coppercoat anti-fouling as well as a potable water coating. This highly modified resin system has been injected with a one-of-a-kind infusion of ceramic particles to improve performance and provide exceptional protection. 

Applications:

  • Marine vessels
  • Potable water systems

Coverage:
130 SF/Gallon. 2 coats are recommended
65 SF coverage/ gallon with 2 coats Finished Applied

Have questions about the application, contact the customer support team today: 

(800) 567-5358

SOLD IN A 1-GALLON UNIT KIT THAT INCLUDES PARTS A & B.  NO RETURNS FOR CERAM KOTE PRODUCTS.  

Mix at a volume ratio of 2 parts A to 1 part B by weight or volume. Do not apply if temperatures are below 40*F.

PRODUCT SPECS

CERAM KOTE MARINE BARRIER COAT 

SHIPPING TIME

Call (800) 567-5358 for pricing and logistics questions 

CeRam-Kote 426 orders typically ship from our Florida fulfillment warehouse where a full stock of coating products are maintained.

Most orders ship out 2-3 business days following the order depending on stock levels. Delivery times shown on the shipping map are typical, though not guaranteed.  

SHIPPING MAP

NUMBER OF COATS

Two Coats (each coat 8-10 mils, 200-250 microns)

CERAM-KOTE 426 MIXING INSTRUCTIONS:

Two (2) parts of Part A to one (1) part of Part B by volume

Two (2) parts of Part A to one (1) part of Part B by weight

CeRam-Kote 426 ceramic particles must be placed into full suspension with the resin prior to application.

CeRam-Kote 426 is packaged in two cans, Part A (resin and ceramics) and Part B (curing agent). Shake Part A (coating) with a Cyclone air-powered shaker or mix Part A until all ceramic powders are suspended in the resin. Time required to place ceramics into suspension varies according to temperature and length of material storage time. 

At 72°F (22.2°C), generally a four (4) to six (6) minute shake will place the ceramic powders into suspension. Regardless of time needed, shake all ceramic material into suspension prior to proceeding. Failure to properly mix will keep CeRam-Kote® 426 from performing or curing properly. Check the can to assure all solids are in suspension prior to proceeding to the mixing step.

Combine Part A (coating) and Part B (curing agent) and shake again until both parts are thoroughly mixed (when mixing quart cans only, pour Part A into Part B. Shaking time is temperature dependent, but a two (2) to four (4) minute shake at 72°F (22.2°C) should thoroughly mix the components. However, caution must be used to prevent heat buildup. No induction time is needed before application

CURE TIME

After thoroughly stirring CeRam-Kote® 426, strain it with a standard paint strainer and pour CeRamKote® 426 into the spray equipment. Apply a first pass of eight (8) to ten (10) mils (200-250 microns) WFT. At 72°F (22.2°C), 30-40 minutes is sufficient time for waiting for first pass to set. Apply a second pass of eight (8) to ten (10) mils (200- 250 microns) for a total DFT of sixteen (16) to twenty (20) mils (400-500 microns) DFT. 

Cure time is temperature dependent. Apply additional mils without incurring runs or sags if the finished product requires thicker coverage. Whenever possible, apply second coat in a cross-coat method.

SURFACE PREP

Bonding strength depends on proper preparation of the surface to be protected for long-term performance of the product. The substrate should be free of oil, grease and salt/chloride contamination. Specifications call for a white metal (NACE 1, SSPC-SP5, Swedish Standards SA-3) finish with a 1-2.5 mil (25-62.5 microns) anchor profile. Surface preparation should be no less than a near white (NACE 2, SSPC-SP10, Swedish Standards SA 2½) finish. 

Cleanliness is the most important step to produce a coated surface that will perform and last. Call CERAM-KOTE® COATINGS INCORPORATED for surface preparation recommendations of materials such as aluminum, brass, plastic, fiberglass and/or concrete.

THINNING:

Thinning of CeramKote 426 is not recommended

APPLICATION: 

Barrier Application

An airless sprayer with a minimum 33:1 ratio is recommened. The air source must be dry. Use reversible carbide tip with orifice size of 0.019-0.021 inches. If applying with roller, use short nap, such as 1/4” (.244 mm). Brush application is also an option.

After thoroughly stirring CeRam-Kote® 426, strain it with a standard paint strainer and pour CeRamKote® 426 into the spray equipment.

Apply a first pass of eight (8) to ten (10) mils (200-250 microns) WFT. At 72°F (22.2°C), 30-40 minutes is sufficient time for waiting for first pass to set. Apply a second pass of eight (8) to ten (10) mils (200- 250 microns) for a total DFT of sixteen (16) to twenty (20) mils (400-500 microns) DFT. Cure time is temperature dependent.

Apply additional mils without incurring runs or sags if the finished product requires thicker coverage. Whenever possible, apply second coat in a cross-coat method.

When using for potable water:

Max Use temperature = 23°C
Max Product Surface Area/Water Volume Application, cm2 /L = 67.7 For use with 200 gallon tanks or greater and pipe diameter of 24” or greater, not exceeding a surface area to volume ratio of 67.7 cm2 /L

Climate:

Use CeRam-Kote 426 only if the substrate temperature and ambient air temperature is above 40°F (4.4°C). No coating should be permitted when substrate is wet from rain or dew, when surfaces are less than five degrees Fahrenheit (three degrees Celsius) above the dew point and holding or when relative humidity is greater than 85%. Moisture will inhibit the catalyst reaction and CeRam-Kote® 426 will not cure or perform properly.

Holiday Detection:

This product is classified as a thin-film coating and should be tested for defects and holidays using a high voltage holiday detector.

Repairs:

If application of the coating is less than seventy-two (72) hours old and has not been exposed to contamination, repair by wiping with Acetone or MEK and then re-apply CeRam-Kote 426. If contaminated or more than 72 hours old, first sand with appropriate grit sandpaper, then repeat repair process.

Cleanup:

Purge and clean spray equipment within thirty (30) minutes of the final spray. Flush equipment with Acetone or MEK until solvent sprays clear. Disassemble and clean equipment to manufacturer’s recommendations. Material left in spray equipment will solidify and damage equipment. Use precautionary measure applicable to any catalyzed material.

Cleanup:

See individual product label for safety and health data. A Material Safety Data Sheet is available upon request.

Purge and clean spray equipment within thirty (30) minutes of the final spray. Flush equipment with Acetone or MEK until solvent sprays clear. Disassemble and clean equipment to manufacturer’s recommendations. Material left in spray equipment will solidify and damage equipment. Use precautionary measure applicable to any catalyzed material

Revised 2.12.19

STORAGE & SHELF LIFE

Pot life for CeRam-Kote® 426 at 72°F (22.2°C) is approximately 30 minutes. Colder temperatures will increase the pot life and warmer temperatures will decrease the pot life. Keep cans out of direct sunlight to prevent heat buildup.

CeRam-Kote 426 has an indefinite shelf life. Preferred storage/usage is a dry enclosed area under 85°F (29°C) /used within two (2) years. However, if stored more than two years above 85°F (29°C), call CERAM-KOTE® COATINGS INCORPORATED technical support prior to use

RELATED PRODUCTS

CeRam Kote 54 Abrasion & Corrosion Resistant Ceramic Coating - 1 Gal Kit
CeRam Kote 54 Abrasion & Corrosion Resistant Ceramic Coating - 1 Gal Kit
CeRam Kote 54 Abrasion & Corrosion Resistant Ceramic Coating - 1 Gal Kit
CeRam Kote 54 Ceramic Protective Coating

CeRam Kote 54 Abrasion & Corrosion Resistant Ceramic Coating - 1 Gal Kit

$237.09
CeRam Kote 426 for potable water systems ceramic corrosion resistant coating
CeRam Kote 426 for potable water systems ceramic corrosion resistant coating
CeRam Kote 426 Ceramic  - 1 Gal Kit

CeRam Kote 426 Ceramic - 1 Gal Kit

$277.48
Ceramic Coating for wet or unprepped surfaces - CeRam Kote 54 SST
Ceramic Coating for wet or unprepped surfaces - CeRam Kote 54 SST
Ceramic Coating for wet or unprepped surfaces - CeRam Kote 54 SST
Ceramic Coating for wet or unprepped surfaces - CeRam Kote 54 SST

Ceramic Coating for wet or unprepped surfaces - CeRam Kote 54 SST

$248.33
CeRam Kote 426 coppercoat antifouling paint
CeRam Kote 426 coppercoat antifouling paint
CeRam Kote 426 Barrier Coat  - 1 Quart Kit

CeRam Kote 426 Barrier Coat - 1 Quart Kit

$124.09
Ceram Kote 2000 chemical resistant ceramic coating 1 gallon
Ceram Kote 2000 chemical resistant ceramic coating 1 gallon
CeRam-Kote 2000 Logo

CeRam Kote 2000 Internal Pipe and Tank Coating - 1 Gal Kit

$235.68
Ceramic Coating for gas and diesel tanks ceram kote 54 sst
Ceramic Coating for gas and diesel tanks ceram kote 54 sst
Ceramic Coating for Gas and Diesel Fuel Tanks  - CeRam Kote 54 SST
Ceramic Coating for Gas and Diesel Fuel Tanks  - CeRam Kote 54 SST

Ceramic Coating for Gas and Diesel Fuel Tanks - CeRam Kote 54 SST

$248.33
Ceram Kote 54 TZM for aerospace
Ceram Kote 54 TZM for aerospace
CeRam-Kote TZM
CeRam-Kote TZM

CeRam-Kote TZM

$249.75
Ceramic Epoxy Coating for Pitting Repair in Steel - CeRam Kote SPG
Ceramic Epoxy Coating for Pitting Repair in Steel - CeRam Kote SPG
Ceramic Epoxy Coating for Pitting Repair in Steel - CeRam Kote SPG
Ceramic Epoxy Coating for Pitting Repair in Steel - CeRam Kote SPG

Ceramic Epoxy Coating for Pitting Repair in Steel - CeRam Kote SPG

$268.15

TRYING TO MEET A SPEC?

WE CAN HELP!

QUESTIONS?

Call (800) 567-5358
or Email
Monday - Friday 8AM - 5PM PST

SHIPPING NATIONWIDE

*Contiguous 48 States Only