Skip to content

CeRam Kote 2000 Internal Pipe and Tank Coating - 1 Gal Kit

$235.68
SKU CK2000-1GWT
Color

CeRam Kote 2000 is perfect for protecting the internal surfaces of piping and tanks from chemicals and corrosion. The Ceram-Kote ceramic polymer technology provides excellent chemical resistance in harsh environments. is the ideal ceramic barrier coating to protect expensive and critical equipment in extreme and harsh environments. 

This product is engineered to be spray-applied and then air-dried. The coating is applied in a single coat with two passes to achieve a 10-15 mils thick application. 

Ceram Kote is strong, offering increased mechanical properties to the underlying surface substrate providing chemical resistance and preventing metal corrosion. 

Applications:

  • Internals in tanks
  • Blow Out Preventers
  • Secondary Containment
  • Wastewater Treatment Pumps
  • Fuel Tanks
  • Brine Tanks

Does your project need a lot of this product, then contact the customer support team today: 

(800) 567-5358

SOLD IN A 1-GALLON UNIT KIT THAT INCLUDES PARTS A & B. 

Mix at a volume ratio of 4 parts A to 1 part B. Do not apply if temperatures are below 40*F.

PRODUCT SPECS

RUBBERIFIC - PLAYGROUND SWING MAT

SHIPPING TIME

Call (800) 567-5358 for pricing and logistics questions 

Note by default all CeRam-Kote orders ship from our centrally located Texas warehouse where a full stock of ceramic coating products are maintained.

Most orders ship out 2-3 business days following the order depending on stock levels. Delivery times shown on the shipping map are typical, though not guaranteed.  

SHIPPING MAP

CURE TIME

A two-pass film of 8-10 mils DFT (200-250 microns) air dries to a dry touch finish within five (5) hours at 72°F (22.2°C) and dries to a 70% cure in fourteen (14) hours. Cure times lengthen at lower temperatures and shorten at higher temperatures. The coating should be fully cured before placing into service.

SURFACE PREP

Bonding strength depends on proper preparation of the surface to be protected for long-term performance of the product. The substrate should be free of oil, grease and salt/chloride contamination. Specifications call for a white metal (NACE 1, SSPC-SP5, Swedish Standards SA-3) finish with a 2.0- 2.5 mil (50 - 62.5 microns) anchor profile.

Surface preparation should be no less than a near white metal (NACE 2, SSPC-SP10, Swedish Standards SA 2 ½) finish. Cleanliness is the most important step to produce a coated surface that will perform and last. Call CERAM-KOTE® COATINGS INCORPORATED for surface preparation recommendations of materials such as aluminum, brass, plastic, fiberglass and/or concrete.

Black rubber swing mat for playground

MIXING INSTRUCTIONS

Volume Ratio: Four (4) parts of Part A to one (1) part of Part B.

Weight Ratio: Seven (7) parts of Part A to one (1) part of Part B.

CeRam-Kote 2000 contains a high loading of ceramic particles which must be placed into full suspension with the resin prior to application. CeRam-Kote 2000 is packaged in two cans, Part A (base) and Part B (curing agent). Shake Part A (base) with a Cyclone air-powered shaker or mix Part A with a paddle mixer until all ceramic powders are suspended in the resin.

Time required to place ceramics into suspension varies according to temperature and length of material storage time. At 72°F (22.2°C), generally a four (4) to six (6) minute shake will place the ceramic powders into suspension. Regardless of time needed, shake all ceramic material into suspension prior to proceeding.

Failure to properly mix will keep CeRam-Kote 2000® from performing or curing properly. Check the can to assure all solids are in suspension prior to proceeding to the mixing step.

Combine Part A (base) and Part B (curing agent) and stir again until both parts are thoroughly mixed.

THINNING

Adjust viscosity with small amounts of MEK, Acetone, Toluene or Xylene. Maximum recommendation of 15%.

STORAGE & SHELF LIFE

Pot life for CeRam-Kote 2000® at 72°F (22.2°C) is approximately one (1) hour. Colder temperatures will increase the pot life and warmer temperatures will decrease the pot life. Keep cans out of direct sunlight to prevent heat buildup. Preferred storage/usage is a dry enclosed area under 85°F (29°C) /used within two (2) years.

Use CeRam-Kote 2000® only if the substrate temperature and ambient air temperature is above 40°F (4.4°C). No coating should be permitted when substrate is wet from rain or dew, when surfaces are less than 5°F (3°C) above the dew point and holding or when relative humidity is greater than 85%. Moisture will inhibit the catalyst reaction and CeRam-Kote 2000® will not cure or perform properly.

RELATED PRODUCTS

CeRam Kote 54 Ceramic Protective Coating
CeRam Kote 54 Ceramic Protective Coating
CeRam Kote 54 Abrasion & Corrosion Resistant Ceramic Coating - 1 Gal Kit

CeRam Kote 54 Abrasion & Corrosion Resistant Ceramic Coating - 1 Gal Kit

$237.09
Ceram Kote 2000 chemical resistant ceramic coating 1 gallon
Ceram Kote 2000 chemical resistant ceramic coating 1 gallon
CeRam-Kote 2000 Logo

CeRam Kote 2000 Internal Pipe and Tank Coating - 1 Gal Kit

$235.68

TRYING TO MEET A SPEC?

WE CAN HELP!

QUESTIONS?

Call (800) 567-5358
or Email
Monday - Friday 8AM - 5PM PST

SHIPPING NATIONWIDE

*Contiguous 48 States Only